Reasons Why Your Nissan Qashqai Key Fob Won’t Work
The Qashqai has a distinct SUV-like feel due to its bigger dimensions, and the 19-inch wheels on Ti and ST-L models may be a bit spongy at times. The front tyres may lose grip on rough surfaces and its CVT can occasionally display wrist-flexing torque steer.
It is usually caused by a dead coin battery which can be easily replaced in a matter of minutes. Make sure the replacement battery is of the same voltage, size and specifications.
Water Damage
One of the most common reasons a Nissan key fob might display the “key ID is incorrect” message is due to water damage. The key fob comes with rubber seals that protect the chip inside, but prolonged exposure to moisture could cause it to stop functioning properly. It’s common to see this when your key fob was dropped in the ocean or swimming pool. However, it can occur when it becomes wet due to rain or soapy hands.
If your key fob was exposed to water for the course of a long time and you’re not sure, clean it using isopropyl or electronic cleaner. It may also need to be taken to an expert to repair or replace it.
If your key fob is in need to be replaced, it’s a relatively simple procedure. First, ensure that you have a multipack of the right battery (CR2032 3V). Open the front and rear cases using a flathead screwdriver. Remove the metal clips, then remove the battery that was in place and replace it. After reassembling the fob, put the mechanical key back in its place and make sure it operates correctly. If it doesn’t, you’ll need to take it to a nissan qashqai keys Locked in car dealer or a professional auto locksmith to repair the chip. Fortunately the chip isn’t often damaged by water exposure and this shouldn’t be too expensive.
Dead Coin Battery
The coin battery is a second frequent reason why your Nissan Qashqai remote key fob might not work. The batteries last for about 3-5 years, but they will eventually fail if the fob has been frequently dropped. You can replace the battery, but make sure it is the same voltage and same size as the first. If you use another battery, it may cause the key to have an untrue key ID, which can prevent it from paired with your vehicle.
The best method to replace the battery of a coin in the Nissan Qashqai Key Fob is to pry it open using an small screwdriver that has a flat head. Insert the screwdriver into tiny notch at the bottom of the fob and move it around to separate the two halves of the key fob. Remove the old CR2025 battery and replace it with a brand new one, noting the position of the old one within the fob.
Before putting the new battery in place be sure that there is no dirt or water damage on the terminals. If there is, wash the terminals with a small amount of isopropyl alcohol. You’ll also need to ensure that the pole cables are plugged in correctly – they should be connected to the negative and positive poles of the battery respectively.
Troubleshooting
If your nissan tiida key replacement Qashqai key fob stops working after exposure to clean rain or tap water, it may be a sign of an internal chip issue. You’ll need a new keyfob if you can’t solve the issue by changing the battery. If you dropped the key fob on the ground and it stopped working instantly it’s likely due to damage to the internal chip. It is usually possible to get the key fob back to function once more if you remove and clean the chip with paper towel and isopropyl alcohol before putting it back into.
Key ID Incorrect is a typical error you may see on the dashboard of your vehicle. The vehicle is not able to recognize the key fob and therefore will not allow the vehicle to start. This problem can be caused various ways, including water damage, problems that are undetectable in the key fob circuitry or RFID interference.
The key fob will stop working when the 12 volt batteries are not working or provide enough electric current. This can affect the Nissan Qashqai’s keyless system central locking, as well as the ability to start the engine using the key fob. If you are unable to lock or unlock the door manually, you should check the batteries on your key fob to make sure they’re in good shape. Try re-inserting the battery to reset the transmitter.
Reprogramming
If the key fob had not been submerged in salt water, it should be able to come back to life after a quick rinse with clean water. You might also try cleaning your electronic chip with isopropyl alcohol or an electronic cleaner. If none of these work then it might be time to replace the entire key fob by a new one.
If your Nissan Intelligent Key is still not functioning, there may be a problem with the connection between it and your car. To reconnect it, start by turning the key into the ignition, but not starting the car. Continue this process until the hazard light flashes twice. Turn the vehicle off and take away the keys.
Open the fob compartment in your vehicle’s fob compartment. It’s usually in the door jamb, on the handle for the driver’s door or under the armrest. Find the small “program” button and press it. You will hear a chime once the process is complete.
It’s time to put your Intelligent Key to the test. Make sure you press all the buttons on the key while standing at a distance from the car. If the lights flash and the horn sounds this means that the key has been successfully linked to the Nissan. It is also possible to test it in close proximity.
